环氧地坪漆的施工技巧有哪些？环氧地坪漆表面处理 1、新竣工环氧地坪经过养护后方可施工，约28天。 2、清除环氧地坪表面水泥浮浆、粘附的垃圾杂物等。3、用清洗剂彻底清除表面油污。 4、清除积水，使潮湿处彻底干燥。 5、清理伸缩缝，灌浆将伸缩缝填充平整，在伸缩缝处粘贴宽度250px左右的玻璃纤维1道。6、用无尘清扫机及吸尘器清洁地表。 7、环氧地坪表面用无尘打磨机打磨，并用吸尘器彻底清洁。8、环氧地坪表面有洞孔和明显凹陷处用腻子来填补，实干后，打磨，吸尘。平整度要求小于3MM。

What are the construction techniques of epoxy floor paint? Surface treatment of epoxy floor paint 1. The newly completed epoxy floor can be constructed after maintenance for about 28 days. 2. Remove cement slurry and adhering garbage and other debris on the surface of epoxy flooring. 3. Clean the surface oil with cleaning agent thoroughly. 4. Clean up the accumulated water and make the wet place thoroughly dry. 5. Clean up the expansion joint, fill the expansion joint smoothly with grouting, and paste a glass fiber channel with a width of about 250 PX at the expansion joint. 6. Clean the surface with dust-free sweeper and vacuum cleaner. 7. The surface of the floor is polished with a dust-free grinder and cleaned thoroughly with a vacuum cleaner. 8. Putty is used to fill holes and obvious depressions on the surface of the floor. After drying, polish and dust. The flatness requirement is less than 3MM. 涂饰封闭涂料

Finishing Sealing Coatings

1、在处理清洁，平整的地坪表面滚涂环氧封闭底涂料一道。

1. Roll an epoxy sealing primer on the clean, flat surface of the floor.

2、在第一道环氧封闭底漆实干后，滚涂第二道环氧封闭底漆。

2. After the first epoxy sealing primer is dry, the second epoxy sealing primer is rolled on.

3、局部漏涂可用刷子补涂，表面多余的底漆必须在下道工序施工前打磨处理好。

3. Partial leakage can be repaired with brushes. Surface superfluous primer must be polished before construction of the next process.

批刮环氧腻子

Batch scraping epoxy putty

1、用环氧批刮料和石英砂作为第一道腻子，充分搅拌均匀，刮平。

1. Use epoxy batch scraper and quartz sand as the first putty, mix well and scrape flat.

2、用无尘打磨机打磨第一道腻子，并吸尘清洁。

2. Grind the first putty with a dust-free grinder and clean it with vacuum.

3、第一道腻子实干后，用环氧批刮料和石英砂作为第二道腻子，充分搅拌均匀，刮平。

3. After the first putty is dry, use epoxy batch scraper and quartz sand as the second putty, mix well and scrape flat.

涂饰环氧面漆2遍

Paint epoxy topcoat twice

1、在中间层实干后，对中间层进行打磨、吸尘。

1. After the middle layer is dry, polish and dust the middle layer.

2、进行环氧地坪面漆滚涂。

2. Rolling coating of epoxy floor finish.

3、第一道环氧面漆滚涂后，如存在气泡现象应用消泡滚筒，在地坪上来回滚动最后让其自行流平即可。

3. After rolling the first epoxy finish, if there are bubbles, the defoaming drum should be used to roll back and forth on the floor and eventually let it leveled by itself.

4、在第一道环氧面漆实干后，进行第二道环氧面漆滚涂。

4. After the first epoxy finish is dry, the second epoxy finish is rolled.

画线

Draw line

1、环氧地坪施工结束后按图纸指定的区域地点弹线。

1. The bullet line of the designated area after the epoxy floor construction.

2、在规定的画线区域粘贴纸胶带。

2. Stick paper tape in the prescribed drawing area.

3、用细砂纸将胶带内的区域打磨，使其粗糙。

3. Use fine sandpaper to grind the area inside the tape to make it rough.

4、用滚桶将指定颜色的环氧树脂面漆涂刷到表面。

4. Apply epoxy resin topcoat of specified color to the surface with a drum.

地坪漆安全技术要求：

Safety Technical Requirements for Floor Paint:

1、施工场地四周应拉好警戒带和挂好警告牌。

1. Alert belts and warning signs should be put up around the construction site.

2、施工场地四周10米内严禁明火作业，严禁吸烟。

2. Open fire operation and smoking are strictly prohibited within 10 meters around the construction site.

3、涂料和稀释剂应放在通风良好的库房内。

3. Coatings and diluents should be placed in well-ventilated warehouses.

4、工作时注意做好个人防护。

4. Pay attention to personal protection while working.

5、电动工具的使用须有专人负责，做完离场前切断电源。

5. The use of electric tools should be handled by a special person, and the power supply should be cut off before leaving the field.